This is a workaround for a bug in ESP-IDF where the configuration setting
for maximum active TCP sockets (PCBs) is not applied.
Fixes cases where a lot of short-lived TCP connections can cause:
- Excessive memory usage (unbounded number of sockets in TIME-WAIT).
- Much higher risk of stalled connections due to repeated port numbers. The
maximum number of active TCP PCBs is reduced from 16 to 12 to further
reduce this risk (trade-off against possibility of TIME-WAIT
Assassination as described in RFC1337).
This is not a watertight fix for the second point: a peer can still reuse a
port number while a previous socket is in TIME-WAIT, and LWIP will reject
that connection (in an RFC compliant way) causing the peer to stall.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Enables support for the ESP standard DTR/RTS based reboot to bootloader.
Switches from OTG to Serial/Jtag mode to workaround issue discussed
in: https://github.com/espressif/arduino-esp32/issues/6762
Signed-off-by: Andrew Leech <andrew@alelec.net>
This is for boards not covered by the Olimex ESP32 PoE implementation. The
major setting is about the PHY interface configuration.
Tested with esp-idf v5.0.4 and Olimex ESP32 EVB boards.
Signed-off-by: shiggy <mail@shiggytech.de>
Workaround for what appears to be an upstream issue:
https://github.com/espressif/esp-idf/issues/14456
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Regression introduced by 5e692d04 now at MICROPY_HW_USB_CDC is set.
The ARDUINO_NANO_ESP32 specifically builds shared/tinyusb/mp_usb_cdc.c
for the 1200bps reset behaviour. However MicroPython esp32 doesn't yet
use the rest of the shared/tinyusb functionality.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
IDF 3 builds are very old now (it seems like the last successful builds are
from 2021), and the current IDF 5 is stable. So remove IDF 3 variants.
Signed-off-by: Matt Trentini <matt.trentini@gmail.com>
Commit a66bd7a48925d318e1dd6ada756df947ffacdc12 added the
ESP32_GENERIC_C3_USB board (now merged with ESP32_GENERIC_C3) and changed
the brownout detector from the default level 7 (~2.51V) to level 4
(~2.92V).
Raising the level again seems to fix random BOD resets on some of the
cheaper ESP32-C3 dev boards (that likely skimp on power supply
capacitance).
Specifically, this change prevents random resets running multi_bluetooth
tests on ESP32-C3 "SuperMini" board.
Also removed from the LOLIN_C3_MINI board as it seems this config is a copy
of the generic one.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The ESP-IDF default on C3 is primary UART0, secondary USB serial/jtag.
Previously MicroPython configured the primary as USB Serial/JTAG and
manually worked with the UART0 console. However UART0 console stopped
working this way in v5.2.2.
The big change is that CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG is no longer set,
as primary console is UART0. However
CONFIG_ESP_CONSOLE_SECONDARY_USB_SERIAL_JTAG is set and IDF provides a
macro CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG_ENABLED which is set if either
primary or secondary esp_console is USB serial/jtag. So need to use that
macro instead.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Saves code size, MicroPython doesn't appear to rely on any of the missing
formatters (64-bit integers, c99-style named arguments).
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit reworks board variants on the esp32 port. It's a simple change
that moves the board variant configuration from an "if" statement within
`mpconfigboard.cmake` into separate files for each variant, with the name
of the variant encoded in the filename: `mpconfigvariant_VARIANT.cmake`.
Optionally, the base variant can have its own options in
`mpconfigvariant.cmake` (this is an optional file, but all other variants
of the base must have a corresponding mpconfigvariant file).
There are two benefits to this:
- The build system now gives an error if the variant that you specified
doesn't exist (because the mpconfigvariant file must exist with the
variant name you specify).
- No more error-prone if-logic needed in the .cmake files.
The way to build a variant is unchanged, still via:
$ make BOARD_VARIANT=VARIANT
Signed-off-by: Damien George <damien@micropython.org>
This fixes the build for some esp32 and nrf boards (for example
`ARDUINO_NANO_33_BLE_SENSE` and `ARDUINO_NANO_ESP32`) due to commit
c98789a6d8e05acb608afe4b30cf3ca563419b2d. Changes are:
- Allow the CDC TX/RX functions in `mp_usbd_cdc.c` to be enabled
separately to those needed for `MICROPY_HW_USB_CDC_1200BPS_TOUCH`.
- Add `MICROPY_EXCLUDE_SHARED_TINYUSB_USBD_CDC` option as a temporary
workaround for the nrf port to use.
- Declare `mp_usbd_line_state_cb()` in a header as a public function.
- Fix warning with type cast of `.callback_line_state_changed`.
Signed-off-by: Damien George <damien@micropython.org>
There are a few TinyUSB CDC functions used for stdio that are currently
replicated across a number of ports. Not surprisingly in a couple of cases
these have started to diverge slightly, with additional features added to
one of them.
This commit consolidates a couple of key shared functions used directly by
TinyUSB based ports, and makes those functions available to all.
Signed-off-by: Andrew Leech <andrew@alelec.net>
This workaround makes sure that all ringbuf functions that may be called
from an ISR are placed in IRAM. See
https://github.com/espressif/esp-idf/issues/13378
Note that this means that all esp32-og builds get non-ISR ringbuf functions
placed in flash now, whereas previously it was just the spiram variant.
This might be a good thing (e.g. free up some IRAM for native/viper).
Fixes issue #14005.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Added a 4MiB flash partitioning variant for ESP32S3: adds support for 4MiB
discrete flash boards or ESP32-S3FH4R2 with embedded 4MiB flash based ones.
Tested on the waveshare ESP32-S3 Mini w/ESP32-S3FH4R2.
Signed-off-by: Stanislav Ponomarev <me@stasponomarev.com>
The new IDF v5.2 deprecated the task cleanup callback we use, so support
for the new option has been implemented in the previous commit. This also
requires a change in the sdkconfig, via a new variable
${SDKCONFIG_IDF_VERSION_SPECIFIC} which is used in all mpconfigboard.cmake
files to include an extra sdkconfig file based on the IDF version in use.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
The legacy I2S "shim" is removed and replaced by the new I2S driver. The
new driver fixes a bug where mono audio plays only in one channel.
Application code size is reduced by 2672 bytes with this change. Tested on
ESP32, ESP32+spiram, ESP32-S3 using example code from
https://github.com/miketeachman/micropython-i2s-examples
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
The Python BLE IRQ handler will most likely run on the NimBLE task, so its
C stack must be large enough to accommodate reasonably complicated Python
code (eg a few call depths). So increase this stack size.
Also increase the headroom from 1024 to 2048 bytes. This is needed because
(1) the esp32 architecture uses a fair amount of stack in general; and (2)
by the time execution gets to setting the Python stack top via
`mp_stack_set_top()` in this interlock code, about 600 bytes of stack are
already used, which reduces the amount available for Python.
Fixes issue #12349.
Signed-off-by: Damien George <damien@micropython.org>
The standard Arduino pinout uses LEDR/G/B and LED_BUILTIN (if available).
This patch adds aliases to match the standard pinout, while retaining
LED_RED/GREEN/BLUE for compatibility with existing scripts and examples.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Instead, configure the default once at compile-time. This means the GAP
name will no longer be set to default after re-initializing Bluetooth.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
Disable unused EC curves and default certificate bundle which is not
implemented in MicroPython. This reduces the firmware size significantly.
This follows commit 68f166dae9ad6dfd94038d5f4394defbb44238af.
Signed-off-by: Carlos Gil Gonzalez <carlosgilglez@gmail.com>
The installation instructions for ESP32 TinyPICO board contained a typo
that used a non-standard baud rate 912600 instead of 921600. This made the
upload command fail on some Windows computers.
Signed-off-by: Scott Zhao <zhaomh1998@outlook.com>
The amount of free IRAM in ESP32 SPIRAM builds is very small and went over
the limit due to commit 30b0ee34d3a7cf6f967387e783268c8a939e04c8. This
commit enables further optimisations to reduce IRAM usage.
Signed-off-by: Damien George <damien@micropython.org>
At some point the config changed such that no messages above Error level
were compiled into the final binary.
Fixes issue #12815.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit changes the Arduino board identifiers to correspond to their
official names. This helps to identify boards at runtime. At the moment
the Arduino Portenta H7 is reported as PORTENTA which is unfortunate as now
there is another Portenta board (Portenta C33) supported in MicroPython.
Also made the other identifiers for flash and network name consistent,
removed the incorrectly used MICROPY_PY_SYS_PLATFORM identifiers, and added
missing MICROPY_PY_NETWORK_HOSTNAME_DEFAULT identifiers.
Boards affected:
- stm32: ARDUINO_PORTENTA_H7, ARDUINO_GIGA, ARDUINO_NICLA_VISION
- renesas-ra: ARDUINO_PORTENTA_C33
- esp32: ARDUINO_NANO_ESP32
- rp2: ARDUINO_NANO_RP2040_CONNECT
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
