Recent MSVC versions have changed the definition of NAN to a non-constant
expression! This is a bug, C standard says it should be a constant.
Good explanation and workaround at: https://stackoverflow.com/a/79199887
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The micro:bit board (and probably other boards using the music or display
module) locked up on soft reboot. Reason was a buffer overflow caused by
an index counter, which was not reset on soft_reboot.
That's fixed in this commit. Tested with a micro:bit board, performing a
series of soft reboots.
Signed-off-by: robert-hh <robert@hammelrath.com>
This fixes a bug in FrameBuffer.ellipse where it goes into an infinite loop
if both radii are 0.
This fixes the bug with a simple pre-check to see if both radii are 0, and
in that case sets a single pixel at the center. This is consistent with the
behaviour of the method when called with just one of the radii set to 0,
where it will draw a horizontal or vertical line of 1 pixel width.
The pixel is set with setpixel_checked so it should handle out-of-bounds
drawing correctly.
This fix also includes three new tests: one for the default behaviour, one
for drawing out-of-bounds, and one for when the sector mask is 0.
Fixes issue #16053.
Signed-off-by: Corran Webster <cwebster@unital.dev>
Closes#13178.
TouchPad confirmed working on both chips, and fixes the the ESP32-S3
reading constant max value. Was unable to reproduce the bug on ESP32-S2 but
this may be due to my test setup, and it still works with the fix.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
ESP32 has hardware V1 and S2/S3 has V2, and future chips
may have different versions.
This should still compile to the same binary before and after.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
- Previously the call to esp_wifi_set_channel() would be immediately
overridden by calling esp_wifi_config(...) with the previous channel set.
- AP interface doesn't seem to need more than esp_wifi_config(...) to work.
It will automatically configure 40MHz bandwidth and place the secondary
channel using similar logic to what was being explicitly calculated here.
- However, calling esp_wifi_set_channel() on the STA interface is necessary
if using this interface with ESP-NOW (without connecting to an AP). So
the esp_wifi_set_channel() call is kept in for this purpose. Without
this, tests/multi_espnow/70_channel.py fails.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Configuring the AP for cyw43 writes to some buffers that are only sent to
the modem when the interface is brought up. This means you can't configure
the AP after calling active(True), the new settings seem to be accepted but
the radio doesn't change.
This is different to the WLAN behaviour on other ports. The esp8266 port
requires calling active(True) on the AP before configuring, even.
Fix this by bouncing the AP interface after a config change, if it's
active. Configuring with active(False) still works the same as before.
Adds a static variable to track interface active state, rather than relying
on the LWIP interface state. This is because the interface state is updated
by a driver callback and there's a race: if code calls active(True) and
then config(a=b) then the driver doesn't know it's active yet and the
changes aren't correctly applied.
It is possible this pattern will cause the AP to come up briefly with the
default "PICOabcd" SSID before being reconfigured, however (due to the
aforementioned race condition) it seems like this may not happen at all
before the new config is applied.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The `num_stas` was uninitialised and if it happened to take the value 0
then no results were returned. It now has the correct maximum value.
Signed-off-by: Damien George <damien@micropython.org>
This function is documented to return True if any stations are connected to
the AP. Without this fix it returns True whenever the driver has brought
the AP interface up.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Commit f4ab9d924790581989f2398fe30bbac5d680577f inadvertently broke some
Python block devices, for example esp32 and stm32 SDCard classes. Those
classes return a bool from their `readblocks` and `writeblocks` methods
instead of an integer errno code. With that change, both `False` and
`True` return values are now be interpreted as non-zero and hence the block
device call fails.
The fix in this commit is to allow a bool and explicitly convert `True` to
0 and `False` to `-MP_EIO`.
Signed-off-by: Damien George <damien@micropython.org>
Because the `ai_canonname` field is subsequently used.
ESP32_GENERIC_S3 (at least) crashes with IDF 5.2.3 without this set.
Signed-off-by: Damien George <damien@micropython.org>
This fixes a regression in db59e55fe7a0b67d3af868990468e7b8056afe42: prior
to that commit `mpremote` supported trailing slashes on the destination of
a normal (non-recursive) copy.
Add back support for that, with the semantics that a trailing slash
requires the destination to be an existing directory.
Also add a test for this.
Signed-off-by: Damien George <damien@micropython.org>
mpremote error messages now go to stderr, so make sure stdout is flushed
before printing them.
Also update the test runner to capture error messages.
Signed-off-by: Damien George <damien@micropython.org>
Seemingly ESP-IDF incorrectly marks RTC FAST memory region
as MALLOC_CAP_EXEC on ESP32-S2 when it isn't. This memory is
the lowest priority, so it only is returned if D/IRAM is exhausted.
Apply this workaround to treat the allocation as failed if it gives us
non-executable RAM back, rather than crashing.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The cleanup in 548babf8 relies on some functions not available in older
ESP-IDF. Temporarily restore them, until we drop support for ESP-IDF <5.2.
PWM functionality should end up the same regardless of ESP-IDF version, and
also no different from MicroPython V1.23.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This was missed in 628abf8f25a7705a2810fffe2ca6ae652c532896. The the bug
was that, when IPv6 is enabled, the `sizeof(ip_addr_t)` is much larger than
IPv4 size, which is what's needed for IGMP addressing.
Fixes issue #16100.
Signed-off-by: Damien George <damien@micropython.org>
In `deque_subscr()`, if `index_val` equals `self->alloc`, the index
correction `index_val -= self->alloc` does not execute, leading to an
out-of-bounds access in `self->items[index_val]`.
The fix in this commit ensures that the index correction is applied
whenever `index_val >= self->alloc`, preventing access beyond the allocated
buffer size.
Signed-off-by: Jan Sturm <jansturm92@googlemail.com>
The PIC16 port didn't catch up with the other ports, so it required a bit
of work to make it build with the latest version of XC16.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
This commit fixes PWM configuration across C3, C6, S2 and S3 chips, which
was broken by 6d799378bad4474e77ddb2fa2187ecd6e290e0ba. Without this fix
the PWM frequency is limited to a maximum of 2446Hz (on S2 at least).
Signed-off-by: Andrew Leech <andrew@alelec.net>
The variable `written` was being used before it was defined in the
`fs_writefile()` method of the Transport class. This was causing an
`UnboundLocalError` to be raised when the `progress_callback` was not
provided.
Fixes issue #16084.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
This brings in:
- requests improvements with overriding headers
- use non-u versions of built-in modules, including asyncio
- fix to logging so StreamHandler calls parent constructor
- various fixes to usb-device packages
- fixes to lora sx126x and sx127x drivers
- improvements to unix-ffi/sqlite3
- support additional gap_connect arguments in aioble
Signed-off-by: Damien George <damien@micropython.org>
This commit enables the implementation of alternative mbedTLS cryptography
functions, such as ECDSA sign and verify, in pure Python. Alternative
functions are implemented in Python callbacks, that get invoked from
wrapper functions when needed. The callback can return None to fall back
to the default mbedTLS function.
A common use case for this feature is with secure elements that have
drivers implemented in Python. Currently, only the ECDSA alternate sign
function wrapper is implemented.
Tested signing with a private EC key stored on an NXP SE05x secure element.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is necessary for mbedTLS callbacks that do not carry any user state,
so those callbacks can be customised per SSL context.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Because VfsLfs2 uses time_ns to create timestamps for files, and for the
test to give consistent results it also needs to use this same function.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, `tests/extmod/vfs_lfs_mtime.py` would fail when run
after the `tests/ports/rp2/rp2_lightsleep.py` test, because
`time.time_ns()` would have a large and constant offset from `time.time()`.
Fix this by re-syncing the time-ns offset when coming out of lightsleep.
Signed-off-by: Damien George <damien@micropython.org>
This previously passed on some targets that automatically import the
`machine` module in `boot.py`.
Signed-off-by: Damien George <damien@micropython.org>
